Re: Help me please find old firmware.
Igor, Do you have a location where I can upload the version 23 BMC for the SE7520JR2? We can't post files here. It's only 970 KB. John
View ArticleRe: RS2BL080 raid external enclosure
For ref I pulled the drives and flashed. When I rebooted with the drives in do palliatives about some kind of pd sync issue. Went into the bios, exited and rebooted and didn't show again. THanks. JR
View ArticleRe: S1200BTLR perhaps defective?
As I understand, the problem occurs when you are using USB sockets from chassis which are connected to outstanding pins from motherboard. Does it also occur when you plug devices to the rear USB...
View ArticleRe: Does S1200KPR really need a graphics card?
This is pretty ****. I have wasted a ton of money on these parts, because your documentation is hopeless. I'd suggest you look at making this much clearer.
View ArticleRe: What is Independent Channel Mode?
Sorry, typo in my original post. I am using DIMM_A1 and DIMM_B1 when I get kernel panics. I've been testing DIMM_A1 alone with each piece of memory to confirm there are no errors on each individual...
View ArticleRe: "0146 - PCI out of resource" blocks POST of our S2600IP-based system
Hmm, Not a simple card and very likely to get very deep real quick I could start by blaming the card, but 1) that is rude and 2) why would anyone do that without supporting data? Selected MMIO size of...
View ArticleRe: S2600CP2 and Fan Noise
Hi Edward,I can still see BMC error.Could you please check the loghttps://www.dropbox.com/s/w8yk8kjn7puwdli/LogFiles.zip
View ArticleClik here to view.
Re: S2600CP2 and Fan Noise
I am using Intel Xeon E5-2620 and Intel AUPSRCBTP Heat Sink. Could you please check whether heatsink direction is ok ot not ?Also, When I attached the airduct,close the case and start the server,...
View ArticleClik here to view.
Re: S2600CP2 and Fan Noise
There are CPU 1 thermal errors reported in the SEL. Heatsink direction seems correct, but air duct is not properly installed. See the attached picture. Notice the two latches in red circles.
View ArticleRe: S2600CP2 and Fan Noise
Thanks Edward. I have fixed the airduct and close the case. The status light turned red after some time and blinking.Then I run the BIOS update again. Here is the log...
View ArticleClik here to view.
Re: S2600CP2 and Fan Noise
Again CPU1 is getting hot. I would double check the installation of the heatsink, and make sure the air flow is not blocked by anything. Pay attention to cable routing - no cable should go between fans...
View ArticleRe: S1200BTLR perhaps defective?
I understand that you are using the newest version of firmware. Have you tried complete BIOS reset (I mean: using jumper on motherboard)? I also assume, that USB devices are not faulty, cables and...
View ArticleRe: S1200BTLR perhaps defective?
All usb devices work fine on others workstations, with same cables. However, I did not try complete bios reset via jumper, having fear of messing things even worse. If I'll reset bios via jumper, it...
View ArticleRe: S1200BTLR perhaps defective?
>> If I'll reset bios via jumper, it will be brought to factory version?Yes, you can do this safely, without any worry.
View ArticleLSI SAS 3000 (4-port 1064e) firmware update?
Hi, Can somebody tell me how to upgrade the onboard SAS controller firmware of an S5000PSLSASR board?I have read the instructions: ================Update Instructions================Warning: If...
View ArticleS5000VSA to S5000PSL
Dear Tech, I have a server with S5000VSA with some reason the motherboard is not working anymore, can i transfer the CPU and RAM belong to S5000VSA to new S5000PSL motherboard ? Any conflict ? I hope...
View ArticleRe: "0146 - PCI out of resource" blocks POST of our S2600IP-based system
Thanks for not punting on the DSP card. It may well turn out to be a card issue but the vendor is not convinced based on my description to this point. I need a more definitive way to either implicate...
View ArticleRe: "0146 - PCI out of resource" blocks POST of our S2600IP-based system
You can see why I thought this could get very deep very fast (and why so support lines want to just blame the other guy.) I should put in the standard disclaimer that “you should always select devices...
View ArticleClik here to view.
Re: S1200BTLR perhaps defective?
Sorry to hear that Please attach settings from BIOS -> Advanced -> USB Configuration. This may sound unrelated, but set in BIOS following options: Advanced -> PCI ConfigurationDual Monitor...
View Article