Re: RAID Card crashes after firmware driver update
What controller are you using Tumi? Regards,John
View ArticleRe: RS2BL080 controller and installing larger drives
You will lose the extra 1TB if you add the new 4TB disk to existing array. Or you can create another VD using the new disk to use up all the capacity.
View ArticleIntel Serverboard S1200BT Wake on Time possibilities?
S1200BTHello Community,does anyone of you have the S1200BT and can confirm to me that this Board does not have Wake on Time?The Bios we have is from 12/05/2012. There is one newer Bios from 12/2012 but...
View Articless4000-e raid failed after single disk replacement
Hello, i have a ss4000-e running a raid10 on which one disk was about to fail.Its led turned yellow, i rebooted the unit and after some hours it was fine again and the led was green.Since it was some...
View ArticleRe: RAID Card crashes after firmware driver update
Tumi, That issue was documented to have been resolved in firmware version v1.12.00-0310, which is quite old. The release notes specifically state: Fixed: Driver detected possible FW hang, halting FW....
View ArticleSC5650UP and S3420GP Full/Min Alternating Fan Speed Problem at system idle
I have a S3420GP board and SC5650 server chassis. After upgrading to the latest BIOS in order to support over 2TB hard drives, at system idle my system fans now alternate between full speed and...
View ArticleClik here to view.
Re: SC5650UP and S3420GP Full/Min Alternating Fan Speed Problem at system idle
Woo-Hoo, figured it out. Server ProductsFans ramp up and down or fans boost after operating system is loadedAfter updating to the latest BIOS and loading the BIOS default values, the system may...
View ArticleRe: RAID Card crashes after firmware driver update
John I did install the latest driver for Windows 8, which is version 6.600.23.00. The firmware version I used is 11.0.1-0057. Right now, I've downgraded the driver back to the generic one from Windows....
View ArticleRe: ss4000-e raid failed after single disk replacement
If your firmware version is 1.3 or lower, you may waht to try the loss of system access recovery script and recovery script use instructions.
View ArticleRe: ss4000-e raid failed after single disk replacement
Hi,i have 1.4 build 10.While waiting for any intel solution, i was trying to read the disks using a linux box.I have a pc running lubuntu and, plugging an old disk of the nas i replaced last year,it...
View ArticleRe: Intel Serverboard S1200BT Wake on Time possibilities?
Edit: Es handelt sich exact um das Board S1200BTL
View ArticleRe: RHEL 5.5 ESRT2 RAID driver (megasr) issue
The driver [2] is the latest. You may need to extract the image to a USB floppy drive. Also while booting from DVD press esc key to give 3rd party driver using the following commands: Linux dd...
View ArticleRe: S3420GPLC-based system does not recognize size of Seagate ST4000NM0033 4...
Are you trying to install OS on it, or you just hook it up to an existing Windows installation as data disk?
View ArticleRe: RAID Card crashes after firmware driver update
Tumi, You can back rev the firmware. We do it often in our lab. HOWEVER, I would not do it in your situation without a tested backup just in case something went wrong. You should always backup critical...
View ArticleS5000VSA Need Help Restoring RAID Array after Configuration Cleared
I need assistance in trying to reconnect/recreate my RAID arrays on an Exchange Server. I think what I need most is to find out from the existing HDDs (undamaged) what the size and stripe...
View ArticleRAID 1 S5520HC with HDs SATAIII
Hi!!My server have a S5520HC mother board with Intel® Embedded Server RAID Technology II. The manual of the S5520HC mother board sais as follows: 'The Intel® Server Board S5520HC/S5500HCV provide an...
View ArticleRe: RAID 1 S5520HC with HDs SATAIII
Ideally SATA 6Gb/s drives should work with SATA II controllers. But remember it's always recommended to use drives in the Tested memory and hardware list. We do have some SATA 6Gb/s drives in the list.
View ArticleServer board S5000PSLSASR and raid issue
I have a server with the board S5000PSLSASR, that is currently deployed. I checked the Raid Web Console, and it shows my array, but under Physical in lists 4 copies of the same bad drive, it says...
View ArticleRaid 1 degrade on s2600cp
Dear sir, We are Intel Platinum Partner in Bangladesh (Flora Ltd.). We need emergency help. After raid 1 configuration successfully by Intel ESRT* II on server board s2600cp with two brand new 500gb...
View Article