SE7501HG2. Can it run the E5-1607 v2 Xeon?
My board is nearly 10 years old. In the Intel pages, there is one which lists Server Products, and for the SE7501HG2 there is a list of "Supported processors".Intel� Server Board SE7501HG2...
View ArticleS2600CP4 with P4308XXMFEN: FANs ride full speed!!!
Installed latest BIOS, FRU, SDR & so on. Tried to change in BIOS - acousting section - no changes. Looked in sysinfo utility's log file - many strings about redundancy fan failure. But I have in...
View ArticleRe: SE7501HG2. Can it run the E5-1607 v2 Xeon?
Ch - Sadly, no, that won't be possible. If you look at the rest of that table, the 3.00GHz must also have a system bus speed of 400 MHz, and the table even provides the order code of the one that...
View ArticleRe: SE7501HG2. Can it run the E5-1607 v2 Xeon?
Dan_0, Thank you very much. However, I am not familiar with "system bus speed". In the server-board product specification it says: "The Intel Server Board SE7501HG2 accommodates one or two 400MHZ FSB...
View ArticleRe: SE7501HG2. Can it run the E5-1607 v2 Xeon?
Dan O is correct, The FSB (front Side Bus) which ran at 400Mhz or 533mhz between the processors & the North Bridge chip which connected to a memory controller and a south bridge chip to PCI slots,...
View ArticleRe: SE7501HG2. Can it run the E5-1607 v2 Xeon?
Thank you both for clarifying the matters; especially the interesting details that follow "Not enough yet?".Case closed. Ch
View ArticleManager servers from Win7-64?
Hello, I'm trying to get remote management working on an older SE7520BD2V server board with the Advanced Edition IMM module installed. The IMM is configured and working properly as I can go to the...
View ArticleRe: S2600CP4 with P4308XXMFEN: FANs ride full speed!!!
Seems the BMC can't get any fan readings. Which fan connectors are you using? Your chassis has two fixed fans, and they should go to Sys Fan 1 and Sys Fan 2.
View ArticleRe: Manager servers from Win7-64?
Did you try to setup another BMC user, besides the default anonymous user?
View ArticleRe: Intel Server System R2312GL4GS JBOD?
The onboard SAS/SATA controller can operate in ESRT2 mode or RSTe mode. ESRT2 doesn't support pass-through, while RSTe does. However, currently Linux is not officially supported on RSTe for this board....
View Articlehdd led is off on intel ATCA-46xx board (Front panel)
Hi, I am koteswararao working on intel based x86_64 board (ATCA-46xx) which hasHDD LED that indicates the status about HDD access . During HDD accessLED is 'ON'. But, after applying sgpio related...
View Articleintegrated BMC web console on S5520HCR motherboard
Hello All, I am trying to get the integrated BMC web console working on an S5520HCR mainboard. I have assigned it an IP address, and I can ping the address and get a response. When I navigate to...
View ArticleRe: integrated BMC web console on S5520HCR motherboard
Do you have RMM3 installed? The embedded web server is only enabled when RMM3 is installed. If you don't have RMM3, you can still use IPMI compliant tools to access the BMC. For more details, please...
View ArticleRe: E10G42BTDA SDK
hi , I am also doing my MSc thesis with 82599es, I also met some problems , do you know whether we can control the sequence of transmitting packets ( i mean sometimes we need transmit control packet...
View ArticleNoise level of FXX1600PCRPS in server P4304CR2LFKN?
I can't seem to find any specifications for the loudness of the fans in the P4304CR2LFKN. I'm looking to build a workstation that I would keep under my desk. It would hold a tesla k20 and two...
View ArticleRe: I need help "Intel S5000PSL" and "Intel xeon E5440"
HiDan, thanks for your response. Nostorywith otherprocessors to performtheupdate. is there any otherwayto perform theupdatefor thismotherboard???? gracias por tu tiempo. regards Alejandro
View ArticleRe: Need to replace USB drive(config)
Yes you can mount two 2.5" SSDs inside the chassis. Refer to page 32 of the Service Guide for details. The two internal drives can be connected to either the onboard SATA ports or your RAID controller,...
View ArticleGhost network adapters in Server 2012
I have a P4208CP4MHGC server with a S2600CP4 motherboard with 4 I350 nic ports. I have also installed an I350T4BLK server adapter with 4 ports.It's running Server 2012 Std. edition with the Hyper-V...
View ArticleRe: Need to replace USB drive(config)
If I mount 2 ssd's could i mirror them encase one where to fail?
View Articles5000psl No display
Hello; I just bought a S5000PSL board (used). i have 2 intel xeon cpus installed as well as 16gb ECC FBDIMM. I have reset the cmos as well as stripping it down to 1 DIMM and still no display. When it...
View Article