Re: Server response slow
Thank you for the comments.After monitoring the server using ‘perfmon’ I got to know that the disk read/write speed seen bit slow. I got these 5 sectors as bad.Perfmon result:Server (C:)\%disk...
View ArticleRe: Dual E5-2643 v3 processors support motherboard
Intel® Server Board S2600WTT Specifications - declared
View ArticleClik here to view.
Remote access to IPMI/BMC on S1200V3RP
I'm trying to get remote LAN access to BMC on S1200V3RP (Rainbow Pass). The IP is set to static configuration with valid IP address on my network, all users are enabled and assigned password in setup,...
View ArticleRe: Wireshark/Tshark on Host SR-IOV Interface
Hi! Do your HP* DL-380 server feature onboard "Intel based 10G NICs" or are these external NIC cards? If these are external Intel(R) Network Cards, would you, please, provide the exact model?
View ArticleRe: Wireshark/Tshark on Host SR-IOV Interface
These are not embedded NICs. They are the HP branded Intel NIC but the chipset is the HP ETHERNET 10GB 2P 560SFP+ ADPTR - Intel Corporation 82599ES 10-Gigabit SFI/SFP+ Network Connection
View ArticleRe: Remote access to IPMI/BMC on S1200V3RP
Did you created at least one user for BMC? Check the procedure from http://download.intel.com/support/motherboards/server/sb/intel_rmm4_bmc_ews_userguide_r2_8.pdf , p.34
View ArticleRe: Remote access to IPMI/BMC on S1200V3RP
Yes, I've done that all. I don't use RMM4, thus I only configured the first IP group (the RMM4 group is greyed out). Addresses for my network are 192.168.1.205 / 255.255.255.0 and 192.168.1.1 for GW....
View ArticleClik here to view.
Re: Remote access to IPMI/BMC on S1200V3RP
Have you tried direct connection to server from notebook via cross-cable?
View ArticleClik here to view.
Problem booting s5520HC
Hi, i have a mother board s5520HC with dual x5675 xeon. I use 4 memory ( type for this mother board) but my workstation can't booting and don;t have dislay, don't show bios. It speak six beeps (short...
View ArticleClik here to view.
Re: Problem booting s5520HC
Power-off, remove the memory completely and try to power-on. If you get the same number of beeps, memory is incompatible.
View ArticleRe: Problem booting s5520HC
I was try but don't have dislay. I installed 2, 4, 8 memory item. 4GB per memory. I was try with HP memory and another memory but all isn't work. I think maybe my mother board have problem?
View ArticleRe: Problem booting s5520HC
Did cables from PSU connected to board well, especially EPS/SSI additional power connectors? Also, you can try with only one CPU installed.
View ArticleRe: Problem booting s5520HC
You can see i was plug 2 6-pin cables and 1 8pin cables, i will try with 1 cpu, but if it is work with one cpu what i do next? Thank you very much!
View ArticleRe: Problem booting s5520HC
The troubling part may be a PSU. Its a Cooler master silent pro gold 1200W, right? This old server MB had a hard requirement of 3.0 A minimum load capacity on +5VSB line (and 5A peak), while this PSU...
View ArticleRe: Problem booting s5520HC
Now i remember a problem. All 7 led (near ram slot ) is off! (when booting or not!). My psu exactly is cooler master silent pro gold 1200ww. Cooler Master: Silent Pro Gold 1200W How to fix my problem...
View ArticleRe: Problem booting s5520HC
This is a expensive Psu with hight power and 80 plus so i don't think it weak.
View ArticleRe: S2600WT2 BMC fails to renew dhcp address
Hi Dan, thanks for taking the time to respond but that's hardly an expected behavior that the udhcp client fails to acquire an IP address from the DHCP server. How is that not a bug? If it's not a bug...
View ArticleRe: Problem booting s5520HC
That`s a desktop PSU, servers have their own PSU requirements. For better understanding: when you press the power on button, first the BMC controller starts, it partially initializes chipset and the...
View ArticleRe: S2600WT2 BMC fails to renew dhcp address
You need to install a Intel® System Configuration Utility (syscfg) to server host OS and issue a syscfg /rbmc command with admin rights.
View Article