If you were running with RAID1 (mirroring), you should be able to look at either drive from that adapter and see the files.
If you were running with RAID0 (striping), you will not be able to see anything unless the RAID Array is operational.
Neither "Big" or "JBOD" support RAID, BTW.
Hope this helps,
...S
Hi k0jiro,
There is no video on the external graphics card, using the Intel® Workstation Board W2600CR and Intel® Xeon® Processor E5-2670 v2.
I was wondering if you have any additional question about video output; feel free to post again if you need anything else.
Regards,
Miguel C.
| Hello Gary, |
Hello ZAID,
Thank you for your time and patience. Like I mentioned before this information is only handled at the engineering level. But, I am still trying to get you some of the information. Could you please help me with this information:
- Is he designing a chassis based on an Intel Server Board?
- Is there a revenue that he will obtain from this?
Best regards,
Henry A.
Hello drock,
So a couple more questions, the logs with 2005 date are actually newer? I was able to see some errors related to the flash device.
In this moment are you still getting the original "BMC FW Health reports the sensor has failed and may not be providing a valid reading." error message?
Regards
Jose A.
Hi David
I sent you complete DiagLogs via email.
Thank you.
Hello Frank,
I know you mentioned you even bought an additional S5520HC platform to attempt the install but, are you using the same ram memory?
I just would like to see if there is a chance you have a faulty ram memory. Could you download memtest from memtest.org and run it against the ram memory that you are using to see if it throws any errors?
Best regards,
Franklin S.
Intel Technical Support.
Hello YurKro,
Thank you for joining the Intel® Community. I am sorry to hear you are having issues with this matter.
Could you please let us know your server model?
Regards,
Amy C.
after i have disabled onboard VGA,
I'm unable to enable again,
even if i enable it in bios it still dont work
my motherboard (s1200v3RP) work correctly with discreet video cards GeForce GT430 and GT730 but don't want work with GTX 750ti (with ad power) and RX560 (without ad power).
Any body know WHY? Please HELP! (BIOS LAST)
Hello Patrik,
If you have video display, turn off your system, move the BIOS configuration jumper to position 2-3, turn your system on again, after the POST runs, setup will run automatically and the maintenance menu will be displayed.
Press F9 in order to restore the BIOS default options.
You can find more additional information on the technical product specification on page 39.
Once you load the BIOS default settings, turn your system off again, move the BIOS configuration jumper to normal position and check if the VGA port works.
If you do not have any video display, please remove the CMOS battery and remove all power from your system between 10 to 30 minutes, then check if the problem continues.
Finally, please let us know if you are getting any beep code or error message.
Best regards,
Sergio S.
Hi iZabol,
High-end graphics cards not recognized by Intel® Server Board S1200V3RPL.
Reviewing the specifications of the graphics cards, both require PCIe x16 ports on the motherboard and this Intel® board is old now and supports up to PCIe 3.0 x8.
This is the reason the old graphics cards work properly and the new version cards not.
More details of the motherboard at Intel® Server Board S1200V3RPL
https://ark.intel.com/products/71384/Intel-Server-Board-S1200V3RPL
Regards,
Miguel C
Hello Stepans,
I just will like to follow up the information sent, and I am afraid because we did not received any information back we are going to proceed on closing the case.
If there is anything else we can help please feel free to ask.
Best regards,
Henry A.
Henry ,
We Appreciate you extended Support .
Relate to the information requested,
- Is he designing a chassis based on an Intel Server Board?
> Since We Have No access to the Chassis Drawing , We Would need The System Boards To complete the Design [ Mating of boards/ Cabling between boards ] etc. Designing a Chassis Is ruled out but modeling a 3D View of the PCB including system boards is Required.
- Is there a revenue that he will obtain from this?
> Revenue - I'm not pretty sure. Our Current focus Is Working on the proto-build.
Hello intbonne,
I to follow up on your questions on possible compatible board with ATX.
If there is anything else we can help please feel free to ask.
Best regards,
Henry A.
Hello diosim,
We will proceed to mark this thread as resolved. If you have further issues or questions just create a new topic.
Jose A.
Hello ZapBrannigan,
We will proceed to mark this thread as resolved. If you have further issues or questions just create a new topic.
Jose A.
Hello ZAID,
Thank you for your time and patience. I pass on the information provided and I will get back with you as soon as we some information.
Best regards,
Henry A.
Hello SvenniB,
We will proceed to mark this thread as resolved. If you have further issues or questions just create a new topic.
Jose A.
Hello Oliver,
We are going to contact you directly about this situation and once we have a response we will update this thread.
Best regards,
David A.