GT430 - PCIe 2.0 x16
GT730 - PCIe 2.0 x16
GTX750Ti - PCIe 2.0 x16
RX560 - PCIe 3.0 x8 (electrically)
All this ver. of PCIe slots are supported electrically by motherboard according with
https://ark.intel.com/products/71384/Intel-Server-Board-S1200V3RPL
May be problem in BIOS or BIOS configuration?
Em um sistema de servidor Dell R640 com processador Intel Xeon Gold 5118 Skylake que tem barramento de 2400mhz, se esse mesmo CPU tivesse um barramento de 2666mhz, qual seria meu ganho real em desempenho.? Alguém saberia fazer esse calculo?
Intel s1200BTL motherboard
We have compute nodes with 24 cores( 48 threads) and 64 GB RAM (2x32GB). When I run a sample code (matrix multiplication)in one of the compute node in one thread, it takes only 4 seconds. But when I starting more runs (copy of the same program) in the same compute node, the time taken increases drastically. When the number of programs running reaches 24 (I gave maximum 24 since physically only 24 cores are present), the time taken becomes like around 40 seconds ( 10 times less). When I checked the temperature, it is below 40 deg Celsius.
When I searched in the Internet about this issue, I found some people saying that it may be due to slowing down of transfer of data from ram to processor when we run many programs. I was not satisfied with this comment, because the compute nodes are designed to run at maximum load with out much decrease in performance. Also, we are using only 1GB of memory even with 24 programs running. Since we are getting performance reduction of about 1/10, I guess the problem is something else.
no success,
still no VGA out,
The senario was the following,
I was adding a graphic card,
booted up everything works
reboot into Bios,
Disable internal graphics,
reboot to OS,,
everything works,
reboot to Bios,
enable internal graphics
saved changes,
shutdown ,
removed extra graphics card,
booted upp, beeping for no grphics, but booted to os, (tested to RDP to server, ok)
i'm not the only one that have this odd problem
Battery powered SSD - Computer Audio - JPLAY - hi-end audio player for Windows
Thank you for that information.
I am moving your thread to the Servers Community for more assistance regarding this matter.
Regards,
Amy C.
Any succes with these files? If there additional information needed, please let me know.
Hello Patrik,
Please try to perform a BIOS recovery on your system:
1. Copy the recovery file (*.bio) to a bootable USB thumb drive.
You can download the BIOS recovery file here.
2. Place the thumb drive in a USB port of the target system.
3. Shut down the system and unplug AC power.
4. Open the chassis and remove the BIOS Configuration Jumper. See the
Technical Product Specification for details including the location of this jumper. Page 38
5. Power the system on.
6. Wait 2-5 minutes for the update to complete.
7. System will either turn off when the recovery process is completed or it
will prompt you to turn off the system.
8. Remove the thumb drive from the USB port.
9. Replace the BIOS Configuration Jumper.
10. Restart system.
If the problem continues, please send us an screenshot on how are you enabling the onboard VGA on the BIOS
Best regards,
Sergio S.
Hello namshad,
Thank you for joining the Intel® Community.
Before starting with any troubleshooting could you please specify the node, chassis, processor, board, RAM, interconnects and OS models so we could have a better picture about this issue please?
We will be waiting for your info.
Regards.
Jose A.
Hello There,
Hello,
Thank you for your prompt response.
The details of our compute node is as follows:
Chassis: Chenbro RM23608
Processor: E-2560 v4
Board: S2600
RAM: 2x32GB DDR4
We are using ROCKS 6.2 version.
In our lab, we mainly use serial codes only. Also, writing files are almost negligible. So, node to node communication is not important.
Right now I am checking the performance of individual compute nodes only. I am giving load to only one compute node.
Correct, the logs from 2005 embedded in the later 2017 entries are newer. The entries are entered in the order they happened. The BMC error is still happening. I believe the flash error was a flash I plugged in that could be failing.
UP!
Hello Stanislav.il,
I am moving your question to our server support group for proper follow up.
Best regards,
David A.
Hello Crazy80,
I noticed the majority of the errors are related to the controller. There is no information that would make us believe the issue is with the midplane.
Regards,
David A.
Ok we'll try today.
Here is report about server.
Hello everyone, first time posting here.
I am using the TPM 2.0 module AOM-TPM-9665 on a Supermicro X10SDV-TLN4F and I used the example AuthPolicy to provision it, through the uefi shell, and enabled TXT. I followed the instructions at [1].
I did that in order to better understand how I can provision TPM. But now I have created a new AuthPolicy with a custom pass phrase and I want to use this one. The problem is that when I try to clear the old authPolicy, when I run `ResetPlatformAuth.nsh sha256 EXAMPLE` I get the error "Did not satisfy PlatformPolicy Provisioning FAILED Setting PlatformAUth to EMPTY failed". What am I missing? Any suggestions?
I am pretty sure I haven't understood something correctly. If anyone can point me on where I can get more documentation on the correct usage of TPM, I will be grateful.
Hi. I have a server that uses 3-3 Terabyte drives to create a RAID 5 system for data. Had a crash and the Intel manager software said it fixed the problem but Windows Server 2008 R2 does not see it as a drive anymore. Just un-allocated. I need the data off the RAID! Any help please.
no success
still same odd problem
Alright, an update.
I got one E5-2609v1 CPU and Kingston KVR13E9/4IK 4GB memory.
i just installed and tried to start and now i am met with 1 beep, pause, 5 beeps, pause, 2 beeps pause 1 beep.
What does this mean and what should i try now? I get no display still.
Thanks